Payment & Shipping Terms:
|Case:||Stainless Steel Sase||Ambient Tempretaure:||-7 ~ 60 °C|
|Accuracy:||+/- 2% F.S. At 21.1°C||Weight:||1 Lb. 2oz (510g)|
|Dimension:||4-3/4'' Dia. X 2-3/16'' Deep||Specil Features:||Vibration And Shock Resistant (with Liquid Filling)|
grain mill homebrew,
Brewing Accessories Of Micro Low Differential Pressure Gauge With Vibration and Shock Resistant
Pressure is pressure physics, the pressures on the unit that is the size. The atmospheric pressure as the benchmark for measuring smaller or larger than the atmospheric pressure of the instrument, as well as for the measurement of fluid (gas, liquid) pressure instrument called the gauge.
The micro differential pressure gauge used to measure fan and blower pressure, filter resistance, wind speed, furnace pressure, orifice plate differential pressure, bubbles water level and liquid amplifier or hydraulic system pressure. It using frictionless magnetic components, can rapidly measure the micro-pressure air or non-corrosive gases, including positive, negative (vacuum) or differential. No wear, hysteresis and clearance. Not filling, vaporization and freezing. This design has anti-vibration, anti-shake and high overpressure capability, you can guarantee access to high precision. The design impact, shock and overload protection.
Instrument type selection must meet the technical requirements of production. Such as the need for remote transmission, automatic recording or alarm; side is the nature of the medium (such as the temperature of the measured medium height, size viscosity, corrosion, dirt level, whether explosive, etc.) whether the instrument specific requirements, site environmental conditions (such as humidity, temperature, magnetic field strength, vibration, etc.) on the instrument type requirements. Therefore, correctly selected according to the requirements of the process is to ensure the meter type instrument work and production safety an important prerequisite.
Such as a conventional multi-tube manometer spring copper alloy (high-pressure alloy steel), while the ammonia pressure gauge Bourdon tube material but had made of carbon steel (or stainless steel), does not allow the use of a copper alloy. Because the chemical reaction of ammonia with copper, explode, so the ordinary ammonia pressure gauge pressure measurement can not be used.
Oxygen pressure gauge and pressure gauge can be exactly the same as in the general structure and material terms, but must be no oil pressure gauge with oxygen. Because the oil into the oxygen system is easy to cause an explosion. The oxygen pressure gauge at the check, not as the use of oil as a working medium like an ordinary pressure gauge, pressure gauge and oxygen in storage should strictly avoid contact with oil. If you must use oxygen pressure gauge measurements with conventional oil before use must be washed repeatedly with carbon tetrachloride, check carefully until no oil so far.
|Item||micro air differential pressure gauge|
|Gauge Size||4"dia. x 2-3/16"deep.|
|Accuracy||±2% of Full scale ( ± 3% on 0,-100Pa,-125Pa,100mm and ± 4% on -00,-60pa,-6mm ranges)|
|Range available||-20 inHg to 15 psig, (-0.677 bar to 1.034 bar)|
|Over pressure||Relief Plug opens at approximately 25psig(1.72bar) standard gauges only|
|Temperature Limits||20- 140 °F(-6.67 to 60°C)|
|Mounting Orientation||Diaphragm in vertical position , cousult factory for other position .|
|Process connection||1/8”NPT ,dupliate high and low pressure taps –one pair side and one pair back .|
|Standard Gauge accessories||include two 1/8”male NPT plugs for duplicate pressure taps, two 1/8”male NPT pipe thread to Rubber tubing adapters, and three flush mounting adapters with screws.|
|Common Range||Customized Range|
|0 – 30Pa||0 – 400Pa||0 – 2.5KPa||0 – 30KPa||-1~0~1KPa|
|0 – 60Pa||0 – 500Pa||0 – 3.0KPa||-15~0~15Pa||-2~0~2KPa|
|0 – 100Pa||0 – 600Pa||0 – 5.0KPa||-30~0~30Pa||-3~0~3KPa|
|0 – 125Pa||0 – 750Pa||0 – 8.0KPa||-60~0~60Pa||-4~0~4KPa|
|0 – 200Pa||0 – 800Pa||0 – 10KPa||-125~0~125Pa||-5~0~5KPa|
|0 – 250Pa||0 – 1KPa||0 – 15KPa||-250~0~250Pa||-10~0~10KPa|
|0 – 300Pa||0 – 2KPa||0 – 25KPa||-500~0~500Pa|
Contact Person: Cindy Chen
Tel: 0086-137 9040 7437